Clearance hole chart
A clearance hole lets a bolt or screw pass through a part. It is larger than the fastener and is not a tap drill. Inch holes follow ASME B18.2.8 (close, normal, loose). Metric holes follow ISO 273 (fine, medium, coarse).
Look up a clearance hole
ASME B18.2.8 inch clearance holes
Values are the standard’s nominal (minimum) hole diameters, with the usual matching drill. Normal fit is the everyday choice. Close is for accurately located holes; loose leaves more room for coatings or hole-position error. #12 is omitted because it is not tabulated in B18.2.8.
| Fastener | Close fit drill (in) | Normal fit drill (in) | Loose fit drill (in) |
|---|---|---|---|
| #6 | #23 (0.154) | #18 (0.170) | #13 (0.185) |
| #8 | #15 (0.180) | #9 (0.196) | #3 (0.213) |
| #10 | #5 (0.206) | #2 (0.221) | B (0.238) |
| 1/4 in | 17/64 (0.266) | 9/32 (0.281) | 19/64 (0.297) |
| 5/16 in | 21/64 (0.328) | 11/32 (0.344) | 23/64 (0.359) |
| 3/8 in | 25/64 (0.391) | 13/32 (0.406) | 27/64 (0.422) |
| 7/16 in | 29/64 (0.453) | 15/32 (0.469) | 31/64 (0.484) |
| 1/2 in | 17/32 (0.531) | 9/16 (0.562) | 39/64 (0.609) |
| 5/8 in | 21/32 (0.656) | 11/16 (0.688) | 47/64 (0.734) |
| 3/4 in | 25/32 (0.781) | 13/16 (0.812) | 29/32 (0.906) |
| 7/8 in | 29/32 (0.906) | 15/16 (0.938) | 1-1/32 (1.031) |
| 1 in | 1-1/32 (1.031) | 1-3/32 (1.094) | 1-5/32 (1.156) |
ASME B18.2.8 clearance-hole nominal (minimum) diameters and the usual matching drills. The standard also states a maximum for each fit; a slightly worn drill that still stays within that band remains in specification.
ISO 273 metric clearance holes
| Bolt | Fine / close (mm) | Medium / normal (mm) | Coarse / loose (mm) |
|---|---|---|---|
| M3 | 3.2 | 3.4 | 3.6 |
| M4 | 4.3 | 4.5 | 4.8 |
| M5 | 5.3 | 5.5 | 5.8 |
| M6 | 6.4 | 6.6 | 7.0 |
| M8 | 8.4 | 9.0 | 10.0 |
| M10 | 10.5 | 11.0 | 12.0 |
| M12 | 13.0 | 13.5 | 14.5 |
| M16 | 17.0 | 17.5 | 18.5 |
| M20 | 21.0 | 22.0 | 24.0 |
| M24 | 25.0 | 26.0 | 28.0 |
ISO 273 fine, medium, and coarse series. Medium is the usual everyday choice.
Sources
- ASME B18.2.8-1999 (S2021), Clearance Holes for Bolts, Screws, and Studs, close, normal, and loose fit categories for #0 through 1-1/2 in.
- ISO 273, Fasteners — Clearance holes for bolts and screws, fine, medium, and coarse series for metric fasteners.
Disclaimer: These pages are reference charts and planning tools only. They are not a substitute for the published standard, a manufacturer's installation instructions, or an engineer's specification. Torque figures are advisory estimates, not values prescribed by ISO 898-1. US customary charts and UK-only fixing names are kept on separate pages and are never mixed into the same rule. Bolt Reference does not sell fasteners, inspect joints, or certify assemblies.