Metric bolt torque chart
ISO 898-1 defines property classes such as 8.8, 10.9, and 12.9; it does not give a tightening torque. The figures below are advisory estimates from Fastenal’s January 2016 torque-tension chart, computed as T = KDF with clamp load at 75% of proof load. They are not wheel-nut or lug-nut values.
Look up an advisory torque
Pick the coarse-thread size, the property class marked on the head, and the friction condition. The result is Fastenal’s published cell, converted to newton-metres.
Published Fastenal cells, class 8.8 and 10.9, dry and lubricated
Through M8 the source chart is in inch-pounds; from M10 up it is in foot-pounds. Newton-metre values are conversions of those cells (1 in-lb = 0.11298 N·m, 1 ft-lb = 1.35582 N·m), shown to a practical working precision.
| Size (coarse) | Class 8.8 lubricated K=0.15 | Class 8.8 dry K=0.20 | Class 10.9 lubricated K=0.15 | Class 10.9 dry K=0.20 |
|---|---|---|---|---|
| M6 × 1 | 70 in-lb (7.9 N·m) | 93 in-lb (10.5 N·m) | 100 in-lb (11.3 N·m) | 133 in-lb (15.0 N·m) |
| M8 × 1.25 | 169 in-lb (19.1 N·m) | 226 in-lb (25.5 N·m) | 242 in-lb (27.3 N·m) | 323 in-lb (36.5 N·m) |
| M10 × 1.5 | 27.9 ft-lb (37.8 N·m) | 37.2 ft-lb (50.4 N·m) | 39.9 ft-lb (54.1 N·m) | 53.2 ft-lb (72.1 N·m) |
| M12 × 1.75 | 48.7 ft-lb (66.0 N·m) | 64.9 ft-lb (88.0 N·m) | 69.6 ft-lb (94.4 N·m) | 92.9 ft-lb (126 N·m) |
| M16 × 2 | 121 ft-lb (164 N·m) | 161 ft-lb (218 N·m) | 173 ft-lb (235 N·m) | 230 ft-lb (312 N·m) |
| M20 × 2.5 | 244 ft-lb (331 N·m) | 325 ft-lb (441 N·m) | 337 ft-lb (457 N·m) | 450 ft-lb (610 N·m) |
Advisory only. Fastenal states that torque is only an indirect indication of tension, that the nut or tapped hole must have adequate proof strength, and that under- or over-tightening can cause failure or injury. Use the equipment maker’s torque when one is published. Zinc plating, wax, and thread-lockers change K and therefore the torque that produces the same clamp load.
This chart is for coarse-thread metric machine bolts in a free-spinning nut or a full-strength tapped hole. It is not a wheel-nut, lug-nut, or axle-nut chart, and it is not a wrench or socket size chart. Fine-pitch bolts, prevailing-torque nuts, and structural high-strength bolting (for example ISO 14399 / EN 14399 assemblies) use different procedures.
Sources
- Fastenal, “Torque-Tension Relationship for Metric Fasteners,” property classes 4.6, 8.8, 10.9, and 12.9, January 2016, engineer@fastenal.com. Formula T = KDF; clamp load estimated as 75% of proof load; K = 0.15 lubricated, K = 0.20 plain and dry; inch-pounds through M8, foot-pounds from M10. The chart is marked advisory and voluntary.
- ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Bolts, screws and studs with specified property classes, for the meaning of 8.8, 10.9, and 12.9. ISO 898-1 does not specify tightening torque.
Disclaimer: These pages are reference charts and planning tools only. They are not a substitute for the published standard, a manufacturer's installation instructions, or an engineer's specification. Torque figures are advisory estimates, not values prescribed by ISO 898-1. US customary charts and UK-only fixing names are kept on separate pages and are never mixed into the same rule. Bolt Reference does not sell fasteners, inspect joints, or certify assemblies.