UNC thread chart (Unified National Coarse)
UNC here means Unified National Coarse, the coarse 60-degree inch thread in ASME B1.1. It is not a hospital or patient-portal abbreviation. The companion fine series is UNF, on the same basic diameters with a finer pitch.
ASME B1.1 Unified National Coarse
Basic pitch diameter is computed from the ASME B1.1 / Unified basic profile: E = D − 0.649519 × P, where P = 1 / TPI. Tap drills are the usual ~75% engagement shop sizes, which sit near D − 0.97425 × P, rounded to a standard number, letter, or fractional drill.
| Thread | TPI | Basic major D (in) | Pitch P (in) | Basic pitch dia. E (in) | Usual 75% tap drill |
|---|---|---|---|---|---|
| #4-40 UNC | 40 | 0.1120 | 0.02500 | 0.0958 | #43 (0.0890) |
| #6-32 UNC | 32 | 0.1380 | 0.03125 | 0.1177 | #36 (0.1065) |
| #8-32 UNC | 32 | 0.1640 | 0.03125 | 0.1437 | #29 (0.1360) |
| #10-24 UNC | 24 | 0.1900 | 0.04167 | 0.1629 | #25 (0.1495) |
| #12-24 UNC | 24 | 0.2160 | 0.04167 | 0.1889 | #16 (0.1770) |
| 1/4-20 UNC | 20 | 0.2500 | 0.05000 | 0.2175 | #7 (0.2010) |
| 5/16-18 UNC | 18 | 0.3125 | 0.05556 | 0.2764 | F (0.2570) |
| 3/8-16 UNC | 16 | 0.3750 | 0.06250 | 0.3344 | 5/16 (0.3125) |
| 7/16-14 UNC | 14 | 0.4375 | 0.07143 | 0.3911 | U (0.3680) |
| 1/2-13 UNC | 13 | 0.5000 | 0.07692 | 0.4500 | 27/64 (0.4219) |
| 5/8-11 UNC | 11 | 0.6250 | 0.09091 | 0.5660 | 17/32 (0.5313) |
| 3/4-10 UNC | 10 | 0.7500 | 0.10000 | 0.6850 | 21/32 (0.6563) |
| 7/8-9 UNC | 9 | 0.8750 | 0.11111 | 0.8028 | 49/64 (0.7656) |
| 1-8 UNC | 8 | 1.0000 | 0.12500 | 0.9188 | 7/8 (0.8750) |
Basic major diameters and TPI from ASME B1.1. Pitch diameters are the basic-profile values E = D − 0.649519P, rounded to four decimal inches. This is a thread chart, not a medical “UNC chart.” Whitworth (BSW) 1/2 in is 12 TPI, not 13 — see the separate Whitworth page.
Common UNF companions (same diameters, finer pitch)
| Thread | TPI | Basic major D (in) | Usual 75% tap drill |
|---|---|---|---|
| #8-36 UNF | 36 | 0.1640 | #29 (0.1360) |
| #10-32 UNF | 32 | 0.1900 | #21 (0.1590) |
| 1/4-28 UNF | 28 | 0.2500 | #3 (0.2130) |
| 5/16-24 UNF | 24 | 0.3125 | I (0.2720) |
| 3/8-24 UNF | 24 | 0.3750 | Q (0.3320) |
| 1/2-20 UNF | 20 | 0.5000 | 29/64 (0.4531) |
UNF pitches and major diameters from ASME B1.1. Tap drills are the usual 75% shop sizes.
Sources
- ASME B1.1, Unified Inch Screw Threads (UN, UNR, and UNJ Thread Forms), for the Unified standard series, basic major diameters, TPI, and the basic-profile relation E = D − 0.649519P.
- Usual 75% tap drills: nearest standard drill to D − 0.97425P, the widely published shop estimate for about 75% thread engagement. The standard specifies the thread, not a mandatory drill letter.
Disclaimer: These pages are reference charts and planning tools only. They are not a substitute for the published standard, a manufacturer's installation instructions, or an engineer's specification. Torque figures are advisory estimates, not values prescribed by ISO 898-1. US customary charts and UK-only fixing names are kept on separate pages and are never mixed into the same rule. Bolt Reference does not sell fasteners, inspect joints, or certify assemblies.