Machine screw size chart
Inch machine screws are numbered sizes (and fractional sizes from 1/4 in up) with a 60-degree Unified thread. The coarse series is UNC; the fine series is UNF. Diameters and pitches come from ASME B18.6.3 and ASME B1.1.
Number sizes, UNC and UNF
Basic major diameter follows the number-size series used across US machine, wood, and sheet-metal screws: size n has a basic diameter of 0.060 in + n × 0.013 in (so #8 is 0.164 in and #10 is 0.190 in). The thread pitch is not the same as a wood screw of the same number.
| Size | Basic major dia. (in) | Basic major dia. (mm) | UNC (coarse) TPI | UNF (fine) TPI | Usual 75% tap drill, UNC | Usual 75% tap drill, UNF |
|---|---|---|---|---|---|---|
| #0 | 0.0600 | 1.524 | — | 80 | — | 3/64 in (0.0469) |
| #1 | 0.0730 | 1.854 | 64 | 72 | #53 (0.0595) | #53 (0.0595) |
| #2 | 0.0860 | 2.184 | 56 | 64 | #50 (0.0700) | #50 (0.0700) |
| #3 | 0.0990 | 2.515 | 48 | 56 | #47 (0.0785) | #45 (0.0820) |
| #4 | 0.1120 | 2.845 | 40 | 48 | #43 (0.0890) | #42 (0.0935) |
| #5 | 0.1250 | 3.175 | 40 | 44 | #38 (0.1015) | #37 (0.1040) |
| #6 | 0.1380 | 3.505 | 32 | 40 | #36 (0.1065) | #33 (0.1130) |
| #8 | 0.1640 | 4.166 | 32 | 36 | #29 (0.1360) | #29 (0.1360) |
| #10 | 0.1900 | 4.826 | 24 | 32 | #25 (0.1495) | #21 (0.1590) |
| #12 | 0.2160 | 5.486 | 24 | 28 | #16 (0.1770) | #14 (0.1820) |
| 1/4 in | 0.2500 | 6.350 | 20 | 28 | #7 (0.2010) | #3 (0.2130) |
| 5/16 in | 0.3125 | 7.938 | 18 | 24 | F (0.2570) | I (0.2720) |
| 3/8 in | 0.3750 | 9.525 | 16 | 24 | 5/16 in (0.3125) | Q (0.3320) |
Basic major diameters and standard UNC/UNF pitches from ASME B1.1, as used on inch machine screws in ASME B18.6.3. Tap drills are the usual ~75% engagement shop sizes (nearest standard number, letter, or fractional drill), not a separate official ASME drill letter.
A machine screw is intended for a tapped hole or a nut. It is not a wood screw, a drywall screw, or a sheet-metal (self-tapping) screw, even when the number size and major diameter match. For a through hole that should not be tapped, use the clearance hole chart.
Sources
- ASME B18.6.3, Machine Screws, Tapping Screws, and Metallic Drive Screws (Inch Series), for the product and head-dimension standard.
- ASME B1.1, Unified Inch Screw Threads (UN, UNR, and UNJ Thread Forms), for basic major diameters and standard UNC/UNF pitches.
- Usual 75% tap drills are the nearest standard drills to D − 0.97425 × pitch (a widely published shop estimate for about 75% thread engagement). Confirm against the tap manufacturer when the material or percentage of thread is specified.
Disclaimer: These pages are reference charts and planning tools only. They are not a substitute for the published standard, a manufacturer's installation instructions, or an engineer's specification. Torque figures are advisory estimates, not values prescribed by ISO 898-1. US customary charts and UK-only fixing names are kept on separate pages and are never mixed into the same rule. Bolt Reference does not sell fasteners, inspect joints, or certify assemblies.