Wood screw size chart

Inch-series wood screws are specified in ASME B18.6.1. The numbered size sets the basic diameter and the nominal threads per inch. Cut-thread and rolled-thread screws share that thread, but their unthreaded body diameters differ.

ASME B18.6.1 thread and body diameters

A wood screw is a gimlet-pointed thread-forming screw for wood and other resilient materials. ASME B18.6.1 allows a ±10% variation on threads per inch. Cut-thread screws have a tapered shank whose body diameter matches the major thread diameter; rolled-thread screws have a smaller, constant-diameter body.

Nominal sizeBasic diameter (in)Threads per inchMajor dia. max / min (in)Cut-thread body max / min (in)Rolled-thread body max / min (in)Min. thread depth (in)
20.086260.090 / 0.0790.090 / 0.0790.075 / 0.0640.010
30.099240.103 / 0.0920.103 / 0.0920.086 / 0.0750.014
40.112220.116 / 0.1050.116 / 0.1050.095 / 0.0840.016
50.125200.129 / 0.1180.129 / 0.1180.107 / 0.0960.018
60.138180.142 / 0.1310.142 / 0.1310.118 / 0.1070.020
70.151160.155 / 0.1440.155 / 0.1440.127 / 0.1160.022
80.164150.168 / 0.1570.168 / 0.1570.136 / 0.1250.023
90.177140.181 / 0.1700.181 / 0.1700.147 / 0.1360.026
100.190130.194 / 0.1830.194 / 0.1830.157 / 0.1460.030
120.216110.220 / 0.2090.220 / 0.2090.176 / 0.1650.031
140.242100.246 / 0.2350.246 / 0.2350.201 / 0.1900.035
160.26890.272 / 0.2610.272 / 0.2610.214 / 0.2030.038

Thread and body diameters for inch-series wood screws, cut and rolled thread types, as published from ASME B18.6.1. Length tolerances in that standard are +0 / −0.03 in up to 5/8 in, +0 / −0.05 in over 5/8 to 1-1/2 in, +0 / −0.06 in over 1-1/2 to 2-3/4 in, and +0 / −0.09 in over 2-3/4 in.

Cut-thread screws are typically threaded for about two-thirds of the nominal length. Rolled-thread screws are threaded at least four times the basic diameter or two-thirds of the nominal length, whichever is greater, unless the screw is too short for that rule.

This table is not a machine-screw chart. A #8 wood screw is 15 TPI; a #8-32 machine screw is 32 TPI. Drywall and sheet-metal screws share some number-size diameters but have their own thread forms and points. For lead holes, use the pilot hole size chart — those drills are starting points, not B18.6.1 table cells.

Sources

  • ASME B18.6.1, Wood Screws (Inch Series), 1981 edition under stabilized maintenance (S2021). The figures in the table are the standard’s thread and body diameters for cut and rolled types.
  • Public dimensional extracts of that table used for cell confirmation: CDE Fasteners, Wood screw thread and body diameters (ASME B18.6.1).

Disclaimer: These pages are reference charts and planning tools only. They are not a substitute for the published standard, a manufacturer's installation instructions, or an engineer's specification. Torque figures are advisory estimates, not values prescribed by ISO 898-1. US customary charts and UK-only fixing names are kept on separate pages and are never mixed into the same rule. Bolt Reference does not sell fasteners, inspect joints, or certify assemblies.